IS200JPDMG1A is a power distribution board developed by GE. It is a part of the Mark VIe control system. JPDM ensures reliable supply to various components in the system. It receives a 28 V DC input power from external AC/DC or DC/DC converters. It efficiently distributes power to the control system, ensuring consistent and reliable supply to all connected components.
Features
Fuse Protection: Provides fuse protection for all its outputs, safeguarding against overcurrent and short circuit conditions. This ensures the safety and integrity of the connected devices by preventing damage due to electrical faults.
Integration with PDM System: Seamlessly integrates into the Power Distribution Module (PDM) system, enhancing its functionality. It provides feedback through the PPDA I/O pack, allowing for monitoring and control of power distribution parameters.
Multiple Power Buses: Designed to maintain three separate power buses for R, S, and T applications, ensuring isolation and redundancy. Each power bus caters to specific functions or subsystems, minimizing the risk of single-point failures and enhancing system reliability.
Redundancy Options: Jumpers are available to configure JPDM for redundant power supply configurations. These jumpers allow for the creation of a single bus with redundant supplies, ensuring uninterrupted power delivery even in the event of a failure.
Board Connectivity: Two adjacent boards can be wired together, facilitating scalability and expansion of the power distribution system. This feature enables the creation of larger power distribution networks to accommodate growing system requirements.
Outputs
Outputs J1-J3: These connections are designated for either JPDP or JPDL boards. Each circuit is protected by a 10 A, 250 V fuse, typically a Bussmann MDA-10 fuse. These fuses safeguard the connected boards from overcurrent conditions, ensuring their safe operation.
Connections JCR, JCS, JCT: These connections are intended for controller power. Each circuit is equipped with a 10 A, 250 V fuse, typically a Bussmann MDA-10 fuse. These fuses provide protection against overcurrent situations, safeguarding the controller power supply.
Connections JAR, JAS, JAT: These connections are filtered and fused, intended for auxiliary devices. Each circuit is protected by a 3.75 A self-resetting fuse. Self-resetting fuses offer automatic protection against overcurrent events, allowing for uninterrupted operation of auxiliary devices.
P4 Connection: The P4 connection is designated for PPDA (Power Diagnostic Pack) I/O pack power. The maximum allowable current for this connection is 0.25 A. This connection provides power to the PPDA I/O pack, facilitating its operation within the system.
JA1 Connection: The JA1 connection is intended for PPDA power diagnostic pack. It provides a maximum voltage of ±5 V for the power diagnostic pack. This connection is crucial for powering and operating the PPDA power diagnostic pack, enabling diagnostic functions within the system.
Installation
Installation
Mounting Location: Designed to be base-mounted vertically on a sturdy metal bracket within the cabinet dedicated to the Power Distribution Module (PDM). Ensure that the mounting location provides adequate space and accessibility for wiring and maintenance tasks.
Bracket Installation: Securely attach the metal bracket to the designated location within the cabinet, ensuring it is firmly anchored to the cabinet structure. Verify that the bracket provides sufficient support to hold securely in place during operation.
Wiring Connections: Refer to the provided wiring diagrams for clear guidance on connecting power inputs and outputs to the JPDM. Follow the specified wiring configurations to ensure proper distribution of power to the control system components.
Diagnostic Connector Installation: Locate the 50-pin diagnostic connector, labeled as P1/P2, mounted on both the top and bottom of the board. Ensure that these connectors are securely attached to their respective mounting points on the JPDM board.
Cable Management: Organize and route cables neatly to prevent tangling and interference with other components within the cabinet. Utilize cable ties or clamps to secure cables in place and minimize the risk of accidental disconnection.
Verification: Before powering on the system, double-check all connections to ensure they are properly seated and secured. Verify that the JPDM is mounted securely on the metal bracket and that all components are aligned correctly.
Testing: Once installation is complete, perform thorough testing to verify the functionality of the JPDM and its connections. Test each power output to ensure proper voltage levels and continuity.
services we provide
Testing & Repair
Repair and Testing of circuit boards to diagnose ensure functionality to maintain current inventory and retain obsolete circuit boards/modules.
Training
Controls including HMI Training for Engineers, Technicians and Operators with wide variety of practical equipment including Management and Health & Safety.
Purchase
You upgrade equipment and we purchase your surplus inventory to maximize the value of unused or end of life assets.
featured products
IS420UCSBH4A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS220PSCAH1B
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS220PDIAH1B
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS220PDOAH1B
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200STCIH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SSCAH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PPROS1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS230PCAAH1B series used in gas turbine speedtronic control systems.