The IS200TPROH1C is an Emergency Protection (TPRO) terminal board developed by GE. Three PPRO I/O packs are housed on the Emergency Protection (TPRO) terminal board. It has a pair of potential transformers (PTs) for bus and generator voltage input and conditions speed signal inputs for the PPROs. There are three DC-37 pin connectors on it, one on each side of the PPRO pack connectors. A cable leading to a Mark* vie backup trip relay terminal board is accepted by each DC-37. TPROH1C has two pluggable blocks with 24 barrier terminals each.
Important Note:
Do not inadvertently cross-connect the 240 V ac and dc voltages in 240 V ac applications. The peak voltage will be higher than the MOV rating, causing the MOV to fail. Most ac supplies have a grounded neutral, so if an unintended connection between the 125 V dc and the ac voltage is made, the sum of the ac peak voltage and the 125 V dc is applied to MOVs connected between dc and ground. On the other hand, in 120 V ac applications, the MOV rating can endure the peak voltage without failing.
Features:
Pulse rates of magnetic speed pickup range from 2 Hz to 20,000 Hz.
The pulse rate accuracy of the magnetic speed pickup is 0.05 percent of the reading.
Dimensions:
15.9 cm tall x 17.8 cm broad
Technology:
Surface-mount
Operating Temperature:
30°C to 65°C
Diagnostics:
Electronic ID parts on the TPRO board and backup trip relay terminal board are scanned during power initiation. PPRO uses this data to verify that the hardware configuration is correct before initiating normal operations.
Configuration:
When thermocouple inputs are used, all JPX, JPY, and JPZ jumpers should be in the (1, 4, 7, 10) position; when 4-20 mA inputs are used, all JPX, JPY, and JPZ jumpers should be in the (3, 6, 9, 12) position.
Compatibility
TPROH1C - Simplex and TMR Application with PPRO I/O Pack
TPROH1C is a simplex and TMR application that works with the PPRO I/O pack. TPROH1C links to three PPRO I/O packs in TMR systems. TPROH1CD and H12C both accept three PPROH1As for direct attachment and include DC-37 connections for three cables to the backup trip relay terminal boards.
Installation
TPROH1C Installation and Mounting
TPROH1C and a plastic insulator are mounted on a DIN-rail-mounted sheet metal carrier. The TPRO and insulator can also be mounted on a sheet metal assembly that bolts directly into a panel. Typical #18 AWG wires are used to connect speed signals and PT inputs to the terminal block. The TPROH1C barrier terminal block can be removed to replace the board. The TPROH2C is a removable Euro-Block type terminal block that can be plugged in.
Operation
Terminal Connections and Power Output
On terminals 31-48, nine-speed inputs are displayed. The consumer can get P24 output from Terminals 5, 9, and 11. The return path for the P24 output is Terminal 8 (MARET). Oring the 28 V power supply of I/O packs R, S, and T yield the P24 output. P24 V output can be accessed even if any of the I/O packs are turned off. Terminals 6, 10, and 12 are 4-20 ma inputs that are fanned to R, S, and T PPRO connections and are allocated for future control extensions. For the 4-20 ma input, Terminal 8 (MARET) serves as a return path.
services we provide
Testing & Repair
Repair and Testing of circuit boards to diagnose ensure functionality to maintain current inventory and retain obsolete circuit boards/modules.
Training
Controls including HMI Training for Engineers, Technicians and Operators with wide variety of practical equipment including Management and Health & Safety.
Purchase
You upgrade equipment and we purchase your surplus inventory to maximize the value of unused or end of life assets.
featured products
IS420UCSBH4A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS220PSCAH1B
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS220PDIAH1B
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS220PDOAH1B
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200STCIH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SSCAH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PPROS1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS230PCAAH1B series used in gas turbine speedtronic control systems.