IS2020RKPSG3A is a VME Rack Power Supply module developed by General Electric. It's one of the most common VME Rack Power Supply models. Each version has its own set of criteria for input and output.
The component has a 400W output rating. The input voltage is rated at 125 Vdc. The module has a Status ID output, a remote +28V PSA output, and five additional +28V PSA outputs.
The module is designed to fit into the right-hand VME control and interface racks.
Installation
Power Supply Placement: On a sheet metal bracket, the power supply is placed on the right-hand side of the VME rack. At the bottom are the de input, 28 V dc output, and 335 V dc output connections. On the bottom of the updated design is a status connection. A cable harness delivers power to the VME rack mates with two connectors at the top of the unit, PSA and PSB. Each of the five 28 V de power modules powers a VME rack segment. A, B, C, D, E, and F are the headings for these sections. An external peripheral device can be powered via the P28C output or PS28 at the bottom of the power supply. The jumper plug on the bracket to the left of the rack must be shifted from the Normal to the Isolated position below to do this.
To Turn Off the Power Supply:
Loosen the PSA/PSB bracket captive fastener at the module's top front.
Take the PSA/PSB bracket assembly and separate it from the RPSM.
Unplug the bottom connectors.
Loosen the two captive bolts on the front sheet metal bracket.
Slide the sheet metal bracket/power module assembly off the control rack by pulling it forward, disconnecting the four rear side connectors.
Remove the four mounting screws that secure the RPSM to the bracket.
Installing the Power Supply:
Find the supply mounting sheet metal bracket as well as the four mounting screws.
Place the module on the bracket with the face of the module facing the captive fasteners, then install and tighten the four mounting screws.
Slide the module bracket assembly onto the control rack, connect the four rear side connectors, and then tighten the two front captive bolts.
Insert the rear tab of the PSA/PSB assembly into the slot on the bracket positioned at the top rear of the RPSM.
Insert the connection assembly into the RPSM's mating connectors.
Tighten the captive fastener on the PSA/PSB bracket.
Connect the bottom connectors of the power supply.
Operation
User Control: There is only one user control, the power switch, and three status LED indications on the VME Rack power supply. The power switch controls the output voltages of the power supply from the front panel and acts as a fault reset when toggled.
Status LED Indicators:
Yellow LED: Indicates the input power condition.
Red LED: Indicates the presence of a malfunction.
Green LED: Indicates normal operation.
services we provide
Testing & Repair
Repair and Testing of circuit boards to diagnose ensure functionality to maintain current inventory and retain obsolete circuit boards/modules.
Training
Controls including HMI Training for Engineers, Technicians and Operators with wide variety of practical equipment including Management and Health & Safety.
Purchase
You upgrade equipment and we purchase your surplus inventory to maximize the value of unused or end of life assets.
featured products
IS420UCSBH4A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS220PSCAH1B
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS220PDIAH1B
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS220PDOAH1B
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200STCIH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SSCAH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PPROS1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS230PCAAH1B series used in gas turbine speedtronic control systems.