IS400JPDEG1A is a DC Battery Power Distribution Board manufactured and designed by General Electric as part of the Mark VIe series used in distributed control systems. The DC Battery Power Distribution (JPDE) board distributes dc power to terminal boards and other system loads after receiving it from a battery or power source. Resistors are used to center a floating DC bus on Earth, and JPDE helps this by providing voltage feedback via PPDA to identify system ground problems. For two power supplies, it offers inputs. JPDE may function at either 24 V dc or 48 V dc. The PPDA I/O pack's feedback is integrated into the PDM system by JPDE. The maximum current that can be passed through this board when it is constructed normally is its limiting factor. JPDE does not provide power to large 500 W - 24 V input/28 V output power supplies that provide control power for I/O packs.
JPDE I/O CHARACTERISTICS:
A battery can supply power through the 6-pin Mate-N-Lok connector JD1. Positive and negative connections use three connector pins each to provide a sufficient current rating.
Fused four-pin Mate-N-Lok output connectors are JFA, JFB, and JFC. Pins 1 and 2 receive positive power, whereas pins 3 and 4 receive negative power. The pin usage on JPDD J28 and J28X is the same as this. The fuse rating for these connectors is 15 A.
The ground reference jumper is JP1. Normally, there is no hard ground connection made to the dc bus. The ground fault detection system centers the dc bus on the earth. The dc positive terminal operates at 24 V normally, measuring 12 * 24 V above ground, and the dc negative terminal has the same magnitude potential below the earth. By closing jumper JP1, onboard resistors can be used instead of external resistors to center the bus on Earth.
For power supply input, JPS1 and JPS2 are nine-pin Mate-N-Lok connectors. The connector has a 24 A steady state capacity and uses pins 7 and 9 for positive 24/48 V dc and pins 1-3 for 24 V return. A supply status feedback switch receives positive 10 V dc wetting from pin 4 and the return from pin 5.
Four-pin Mate-N-Lok output connections with fuses and switches are designated as JS1, JS2, and JS3. Pins 1 and 2 receive positive power, whereas pins 3 and 4 receive negative power. The pin usage on JPDD J28 and J28X is the same as this. These switched connections have a 7 A fuse rating.
On the top and bottom of the board, respectively, P1 and P2, are two 50-pin diagnostic ribbon cable connectors. A board housing a PPDA I/O pack receives feedback signals from connector P1. The signals leaving connector P1 are sent to the PPDA through connector P2, which also receives feedback from other power distribution boards.
DIAGNOSTICS:
A digital ID specifying the kind, revision, and serial numbers of the board
Two analog feedbacks on battery voltage. A positive bus and a negative bus each have their own. The precision of voltage feedback is 1%.
Three dc branch circuit status indications with switches and fuses
Two dry contact output status indications for dc power converters
Three status indicators for fused branch circuits
For external test equipment, two test points with series 2.15 k resistors are offered on the 24/48 V dc bus.
The positive bus is connected to HW1, and the negative bus is connected to HW2.
CONFIGURATION: When jumper JP1 is engaged, the JPDE supplies local earth connections with 6 k voltage-centering resistors from positive and negative dc. The connection to the ground is unlocked when JP1 is withdrawn. When a floating dc bus needs to be centered on the ground, insert JP1.
Compatibility
The JPDB, JPDF, JPDS, and JPDM feedback signal P1/P2 connectors on the IS200JPDE board are compatible, creating a PPDA I/O pack.
Installation
In a PDM-related cabinet, JPDE is base-mounted vertically on a metal bracket. To route power input and output, consult the wiring diagrams. On the top and bottom of the board, a 50-pin diagnostic connector is installed.
services we provide
Testing & Repair
Repair and Testing of circuit boards to diagnose ensure functionality to maintain current inventory and retain obsolete circuit boards/modules.
Training
Controls including HMI Training for Engineers, Technicians and Operators with wide variety of practical equipment including Management and Health & Safety.
Purchase
You upgrade equipment and we purchase your surplus inventory to maximize the value of unused or end of life assets.
featured products
IS420UCSBH4A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS220PSCAH1B
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS220PDIAH1B
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS220PDOAH1B
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200STCIH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS420UCSBH4A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PSCAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDIAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PDOAH1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200STCIH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SRLYH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS200SSCAH2A series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS220PPROS1B series used in gas turbine speedtronic control systems.
IS200SRLYH2A
Module manufactured by General Electric as part of the IS230PCAAH1B series used in gas turbine speedtronic control systems.